2-6米液壓剪板機適用于電器開關柜,文件柜,廚房用具,汽車尾箱裝璜等產品的板料折彎工序.也可對炭鋼板,不銹鋼板,鋁板,銅板等進行折彎。

我廠生產的2-6米液壓剪板機是一種小型的不用電源的板料折彎設備,它適用于電器開關柜,文件柜,廚房用具,汽車尾箱裝璜等產品的板料折彎工序.也可對炭鋼板,不銹鋼板,鋁板,銅板等進行折彎。

電動剪板機主要用于平面切割非規則圖形，理論上只要用AUTOCAD能畫出來的圖形就能切割（半徑小于2倍等離子割縫寬度的圖形無法切割）。

電動剪板機的使用方法：

剪板機在使用過程中可能產生如下的情況 開動剪板機機器作空轉若干循環，在正常情況下，試剪不同厚度板料，由薄至厚。用戶熟悉剪板機性能。試剪時不同板厚時   調對不同刀片間隙。若不調對相應的刀片間隙，則影響刀片度。3剪板機在剪切過程中打開壓力表開關，觀察油路壓力值，剪12mm板時壓力應小于20MPa。此遠程調壓閥No9，出廠時壓力調定20—22MPa，用戶   遵守此規定，不得為剪超規定材料面提高壓力，造成機器損壞。操作時聲音平衡。剪板機如有雜音，應停車檢查。5剪板機操作時油箱提高溫度<60度 超過時關機休息。